Skip to main content
13 min read Beginner

Hayward Pool Filter Guide: Models, Sizes, and Prices

The short answer

Which Hayward pool filter do you have? ProSeries, SwimClear, and Pro-Grid sizes and prices, how to clean each type, and Hayward vs Pentair sand filters.

In This Guide

Hayward is one of the most common filter brands on residential pool pads in North America, which means many owners inherit one rather than choose it. That leaves a lot of people standing in front of a tank with a faded label, unsure whether they own a sand filter, a cartridge filter, or a DE filter, and unsure which parts, prices, and routines apply to it. This guide sorts the whole Hayward lineup out: what each family is, how to read your model number, what the units and media cost, which parts wear out first, how each type is cleaned, and how Hayward compares with Pentair on sand filters.

Which Hayward Pool Filter Is Right for Your Pool?

For most residential pools, the Hayward ProSeries sand filter is the right choice. It has the lowest purchase price, the simplest routine, and the cheapest long term ownership cost, because the sand media only gets replaced every 3 to 5 years. Choose a Hayward SwimClear cartridge filter instead if you want finer filtration and no backwashing at all, which matters on a well, a water meter, or anywhere wasted water is expensive. Choose a Hayward Pro-Grid DE filter if water clarity is the priority above everything else, since DE filters catch the smallest particles of the three, but expect the most upkeep because the grids need recharging after every backwash and a full teardown once or twice a season.

That is the short version. The rest of this guide fills in the model numbers, sizes, and prices behind each of those three choices.

The Hayward Filter Lineup

Hayward sells three residential filter families. Each one uses a different media, a different cleaning routine, and a different model prefix, so once you know which family you own, everything else follows.

ModelTypeSizePool Size It Suits
S166TProSeries sand16 inch tank, 100 lbs sandSmall above ground pools to about 12,000 gallons
S180TProSeries sand18 inch tank, 150 lbs sandAbove ground and small inground to about 18,000 gallons
S210TProSeries sand21 inch tank, 200 lbs sandMid size inground pools to about 24,000 gallons
S244TProSeries sand24 inch tank, 300 lbs sandStandard inground pools to about 30,000 gallons
S270TProSeries sand27 inch tank, 350 lbs sandLarge inground pools over 30,000 gallons
C2030SwimClear cartridge225 sq ftPools to about 20,000 gallons
C3030SwimClear cartridge325 sq ftPools to about 25,000 gallons
C4030SwimClear cartridge425 sq ftPools to about 30,000 gallons
C5030SwimClear cartridge525 sq ftLarge pools and heavy bather loads
DE3620Pro-Grid DE36 sq ftPools to about 20,000 gallons
DE4820Pro-Grid DE48 sq ftPools to about 25,000 gallons
DE6020Pro-Grid DE60 sq ftPools to about 30,000 gallons
DE7220Pro-Grid DE72 sq ftLarge pools and long swim seasons

The sand loads above are Hayward’s own published figures for the ProSeries tanks, and they are worth treating as exact numbers rather than approximations. Underfilling a sand tank lets water channel down the outside of the bed instead of through it, and overfilling pushes sand up into the multiport valve.

A few notes on how the families differ in practice. ProSeries sand tanks are sold in both top mount and side mount configurations, with the T suffix indicating the top mount version that most residential pads use. SwimClear tanks hold four separate cartridge elements rather than one (eight on the 680 sq ft C7030), so a 425 sq ft C4030 spreads its dirt load over far more pleated fabric than a single element filter of half that area and goes longer between cleanings. Hayward’s other cartridge line, Star-Clear and Star-Clear Plus, uses one element under a lid held by a single locking knob, in sizes such as the 90 sq ft C900 and the 120 sq ft C1200. Pro-Grid DE filters use eight curved, fabric covered grids, seven full size and one short, and the whole assembly lifts out as one unit.

The gallon figures in the table are guidance, not a rule. Filter sizing should follow your pump flow rate and your turnover target, not just pool volume, and oversizing a filter is almost always the better error. Our guide on what size pool filter you need walks through that math.

If you are shopping rather than diagnosing, it is worth comparing tank sizes and valve options side by side before you commit to a model.

Check Hayward Filter Prices on Amazon

How to Identify Your Hayward Model

Every Hayward filter carries a label plate on the tank shell, typically at mid-height on sand and DE tanks and near the base on SwimClear tanks. The plate lists the model number, the filtration area or sand capacity, and the maximum working pressure. That model number is the single piece of information you need before ordering any part.

The prefix convention is consistent across the lineup:

  • S means sand. S166T, S180T, S210T, S244T, S270T.
  • C means cartridge. SwimClear models run C2030 to C7030, and Star-Clear and Star-Clear Plus models use numbers such as C250, C500, C900, and C1200.
  • DE means Pro-Grid diatomaceous earth. DE3620, DE4820, DE6020, DE7220.

The numbers are equally readable once you know the pattern. On sand models, the first digits are the tank diameter in inches: an S180T is an 18 inch tank, an S244T is a 24 inch tank. On SwimClear models, the first digits approximate the filtration area in square feet, so a C3030 is a 325 sq ft filter. On Pro-Grid models, the first digits are the exact grid area, so a DE4820 carries 48 sq ft of grid surface.

If the label is gone, which is common on tanks that have spent fifteen summers in direct sun, identification is still straightforward. First, the type is obvious from the hardware: a multiport valve with a sight glass and no clamp band means sand, a clamp band with no valve means SwimClear, a lid held by a single locking knob means Star-Clear, and a clamp band with a backwash valve plumbed into the side means Pro-Grid DE. Second, for sand filters, measure the tank diameter at its widest point with a tape measure and match it to the table above, which gives you both the model and the correct sand load. Our pool sand filter size chart lists the same figures by diameter and by 50 lb bag count if you are ordering media.

For SwimClear and Pro-Grid tanks with no label, open the tank. The square footage is usually printed on the cartridge end caps or stamped into the grid frames, and that number identifies the model.

Hayward Filter Prices

Hayward pricing splits cleanly along the three families, and the cheapest unit to buy is also the cheapest to run.

  • ProSeries sand filters: roughly 300 to 700 dollars for the tank with a multiport valve, with the S166T at the bottom of that range and the S270T at the top. Media is the cheap part: a full sand change costs 40 to 150 dollars depending on tank size, using #20 silica sand at roughly 10 to 15 dollars per 50 lb bag, and it happens every 3 to 5 years.
  • SwimClear cartridge filters: roughly 400 to 900 dollars for the tank, from the C2030 up to the C5030. The ongoing cost is higher than sand because a full set of four replacement elements runs 200 to 400 dollars and gets replaced every 3 to 5 years.
  • Pro-Grid DE filters: roughly 500 to 1,000 dollars for the tank with valve, from the DE3620 to the DE7220. DE powder adds 20 to 40 dollars a season, and a full grid set replacement is 200 to 350 dollars every 5 to 10 years.

Add installation if you are not doing the swap yourself, which typically runs 150 to 400 dollars for a like for like replacement on an existing pad. Prices move with the season and with supply, so treat these as planning ranges rather than quotes. Our full breakdown of pool filter cost covers unit prices, media, install, and annual ownership across all three filter types.

One cost note specific to Hayward: because the brand is so widely installed, aftermarket parts and cartridges are plentiful and usually 30 to 50 percent cheaper than OEM. Aftermarket elements are a reasonable buy for cartridges, less so for DE grids, where the fabric quality difference shows up in torn grids after two seasons.

Hayward Parts That Wear Out

Hayward tanks outlast their internals by a wide margin. These are the parts that actually fail, in rough order of how often they need replacing:

  • Spider gasket. The star shaped gasket inside the multiport valve on sand and DE filters. It tears when the valve handle gets moved with the pump running, and the symptom is water running out the waste line while the valve sits in FILTER. Typically a 2 to 3 year part.
  • Tank and lid O-rings. The clamp band O-ring on SwimClear tanks and the lid O-ring on sand tanks dry out, flatten, and start weeping. Lubricate them with a Teflon based pool lubricant at every opening and replace every 2 to 3 years.
  • Laterals. The slotted fingers at the bottom of a sand tank that collect filtered water. When one cracks, sand blows back into the pool through the returns. They are only accessible with the sand removed.
  • Pressure gauge. The 1/4 inch NPT gauge fogs, sticks, or freezes at a fixed reading. It is a cheap part and the most important one on the tank, since every cleaning decision depends on it.
  • Cartridge elements and DE grids. These are consumables, not repairs. Replace SwimClear elements as a matched set, and Pro-Grid grids as a full set including the short grid.

Part numbers differ between models that look nearly identical on the pad, so check your model label before ordering anything. Our pool filter parts guide names every component by filter type with typical replacement costs, and for element sizing specifically, see our page on Hayward pool filter cartridges.

For a spare set, search current Hayward replacement filter cartridge listings on Amazon using your exact model number rather than tank height.

How Do You Clean a Hayward Pool Filter?

Clean a Hayward filter when the pressure gauge climbs a set amount above the clean starting pressure: Hayward’s manuals say 8 to 10 PSI for ProSeries sand and Pro-Grid DE filters, and 7 to 10 PSI for SwimClear and Star-Clear cartridge filters. Sand and DE tanks are cleaned by backwashing through their valve. SwimClear and Star-Clear tanks have no backwash port, so they are opened and the elements hosed off by hand. Mark the clean starting pressure on the tank at startup, because every one of those triggers is measured from it.

Hayward familyClean atRoutineElements
ProSeries sand (S166T to S270T)8 to 10 PSI over cleanBackwash until the sight glass runs clear, about 2 minutes or less, then Rinse 1/2 to 1 minuteSand bed
SwimClear (C2030 to C7030)7 to 10 PSI over cleanOpen the tank and hose each elementFour, or eight on the C7030
Star-Clear (C250, C500)7 to 10 PSI over cleanLift out the element and hose itOne, under a locking knob
Pro-Grid DE (DE2420 to DE7220)8 to 10 PSI over the pre-coat readingBackwash about 2 minutes, then add fresh DEEight grids: seven full, one short

On a ProSeries tank, Hayward’s manual has you shut the pump off before every valve change and press the VariFlo handle down before turning it, which protects the valve seal, and Rinse sends the dirty water left after Backwash out the waste line instead of back into the pool. When a backwash stops bringing the gauge back near its starting reading, the sand needs a deeper clean or replacing, covered in how to clean a pool sand filter. The valve steps are in how to backwash a pool filter.

For SwimClear tanks, Hayward’s manual says to hose each element inside and outside, brush the pleats, never pressure wash, and torque the clamp nut back to 150 inch-lbs with a 3/4 inch socket rather than tightening it by hand. It also gives a replacement test: if the starting pressure after cleaning sits more than 6 PSI above the reading the filter had with new elements, replace them at the next cleaning. Single element SwimClear models (C100S, C150S, C200S) and the Star-Clear and Star-Clear Plus lines hold one cartridge, and Hayward’s Star-Clear manual adds a one hour soak in filter cleaner when algae, suntan oil, or body oils coat the pleats. Technique is in how to clean a cartridge pool filter.

Pro-Grid filters are measured from the pre-coat pressure, the reading right after fresh DE goes in, and every backwash is followed by a full charge through the skimmer: 3 lbs for the DE2420, 4.5 for the DE3620, 6 for the DE4820, 7.5 for the DE6020, and 9 for the DE7220. Hayward warns that running more than a minute or two without that coat can damage the grids. For a manual clean it has you backwash, drain the tank, remove the clamp, lift the element cluster out by its handles, and hose it, never pressure wash. Teardown and soaking steps are in how to clean a DE pool filter.

Hayward vs Pentair Sand Filter: Which Should You Buy?

Buy the one that suits your plumbing and the warranty you can actually get, because on filtration the two are evenly matched: Hayward’s 24 inch ProSeries S244T and Pentair’s 24 inch Triton II TR60 both have 3.14 sq ft of filter area. When replacing a filter, matching the brand and valve position already on the pad is usually the simplest swap, because a top mount and a side mount tank plumb differently and each brand’s manual specifies its own valves and internal parts. The differences below come from Hayward’s ProSeries manual and product page and Pentair’s Triton installation and user’s guide.

Hayward ProSeries S244TPentair Triton II TR60
Valve positionTop mount VariFlo, held by a flange clamp that lets it rotate 360 degreesSide mount multiport or two-position slide valve
Opening the tankLoosen the flange clamp and lift off the valveUnscrew the threaded top closure, which goes back hand tight plus 1/4 turn with Pentair’s wrench
LateralsUmbrella-fold assembly that Hayward calls self cleaningIndividual laterals threaded into a hub, reached past a swing-away diffuser
Sand300 lbs325 lbs
Backwash trigger8 to 10 PSI over clean10 PSI over clean
Backwash, then RinseAbout 2 minutes or less, then 1/2 to 1 minuteAbout 3 to 5 minutes, then about 30 seconds

Warranty terms depend on where you buy more than on the brand. Hayward’s residential warranty terms give in-ground filters sold through pool professionals 3 years on parts and 1 year on labor, extended to 3 years of labor through a Hayward Rewards dealer, while its W3 models, which are sold online and in stores, carry 1 year, parts only. Pentair’s warranty page lists filters at 2 years when professionally installed, 3 years as part of a qualifying pump and filter bundle bought from a local seller, and 1 year, parts only, when bought online.

For parts, Hayward sells ProSeries laterals in packs of 10 or as a complete folding assembly, and our Hayward pool filter parts guide covers the numbers, while Pentair lists Triton laterals individually for each tank size. If you like the top mount layout but want Pentair, its Sand Dollar line carries a six-position multiport valve on top; the rest of that lineup is in our Pentair pool filter guide.

The bigger decision is usually filter type rather than brand. A Hayward ProSeries sand filter and a Hayward SwimClear cartridge filter differ far more from each other than either differs from its Pentair equivalent. If you are still choosing between media types, start with our comparison of DE vs sand vs cartridge filters, then pick the Hayward model in that family using the lineup table above.

Whichever you land on, log the clean startup pressure on the tank with a paint pen once the new filter is running. That single number turns every future cleaning decision into a glance at the gauge.

Frequently Asked Questions

Which Hayward pool filter do I have?
Look at the label plate on the side of the filter tank, usually at mid-height or near the base. Hayward model numbers start with a letter code that tells you the type: S for sand (S180T, S244T), C for cartridge (SwimClear models such as the C3030 and C4030, or Star-Clear models such as the C500 and C900), and DE for Pro-Grid diatomaceous earth (DE4820, DE6020). If the label has faded off an older tank, the hardware gives it away. A sand filter is a round tank with a multiport valve on top or on the side, a SwimClear is a tall tank with a clamp band and no valve, a Star-Clear lid is held on by a single locking knob, and a Pro-Grid DE tank has the same clamp band as a SwimClear plus a backwash valve plumbed into its side.
Which Hayward filter is best for most pools?
The ProSeries sand line is the best fit for most residential pools. It is the cheapest to buy, the media only gets changed every 3 to 5 years, and cleaning is a two minute backwash rather than a tank teardown. SwimClear cartridge filters make more sense if you are on a water meter or a well and cannot afford to send hundreds of gallons down the waste line, or if you want finer filtration without adding DE powder. Pro-Grid DE filters produce the clearest water of the three but demand the most attention.
How many square feet is a Hayward SwimClear filter?
The four common SwimClear models run 225, 325, 425, and 525 square feet: the C2030 is 225 sq ft, the C3030 is 325 sq ft, the C4030 is 425 sq ft, and the C5030 is 525 sq ft. The number in the model name is a rough shorthand for the area, so C3030 means roughly 300 plus square feet. Each model uses a set of four cartridge elements sized specifically for that tank, so check your model label before ordering replacements rather than buying by tank height.
How much sand does a Hayward sand filter take?
Hayward publishes a sand load for each ProSeries tank: 100 lbs for the S166T, 150 lbs for the S180T, 200 lbs for the S210T, 300 lbs for the S244T, and 350 lbs for the S270T. Buy #20 silica pool filter sand in 50 lb bags and use the full published load, because underfilling lets water channel around the media and overfilling fouls the multiport valve. Check your model label before you order, since older Hayward tanks of the same diameter sometimes carry different part numbers.
How long does a Hayward pool filter last?
A Hayward filter tank commonly lasts 10 to 15 years, and often longer on a pad that gets winterized properly. The wear items inside fail well before the tank does. Sand media is changed every 3 to 5 years (Hayward support's figure), SwimClear cartridge elements typically last 1 to 3 years, DE grids last until they tear (typically 3 to 5 years), and the spider gasket inside a multiport valve is a 2 to 3 year part on a filter that gets backwashed regularly. Replace the tank itself when the shell cracks or the clamp band area distorts, since neither is safely repairable under pressure.
Pool Filter Guide Editorial Team logo
Pool Filter Guide Editorial Team Independent research site

Pool Filter Guide is an independent research site. Every guide is built from manufacturer owner's manuals, spec sheets, and published standards, and names its source in the text. We do not test products in-house, and no brand pays for placement or a better verdict.

Published: Last updated: