Skip to main content
15 min read Beginner

How to Clean Pool Filter Balls and How Many You Need

The short answer

How to wash pool filter balls by hand or machine, whether they can be backwashed or tumble dried, and how many you need, using each maker's own numbers.

In This Guide

To clean pool filter balls, take them out of the tank, rinse off loose dirt, and wash them in a mesh laundry bag on a cold or synthetics cycle no warmer than 30°C (86°F), with no fabric softener, then air dry them before reloading. That is the method GRE prints for its Aqualoon balls, and Swim & Fun adds that no soap is needed at all. Bestway is the big exception: its Flowclear Polysphere manual says hand wash only, never the washing machine. How many balls you need depends on the brand, because the ratios on the bags range from about 10 g to 31 g of balls per kilogram of sand replaced.

If you are still deciding whether to switch at all, the short version is that balls are far lighter than sand and washable, while sand is cheaper and more forgiving. Our guide to pool filter balls vs sand weighs that decision. This page assumes the balls are already bought and covers loading, running, washing, and replacing them.

How Many Pool Filter Balls Do You Need?

Most brands use about 28 g of filter balls for every kilogram of sand your filter is rated for, which works out to one 700 g pack per 25 kg (55 lb) of sand. That ratio is not universal, though. Fibalon and FilterBalls rate their fiber to replace far more sand per gram, so the number printed on your particular bag always wins.

Here is what each manufacturer states:

BrandTheir published ratioBalls per kg of sand
Bestway Flowclear Polysphere28 g replaces 1 kg of sand (owner’s manual)28 g
Intex fiber ball (manual 342PO)650 g for 23 kg, 1,000 g for 35 kg, 1,500 g for 55 kg27 to 29 g
Swim & Fun Filterballs700 g replaces 25 kg28 g
GRE Aqualoon700 g equals 25 kg28 g
VEVOR filter balls700 g replaces 25 kg28 g
Champlain Filtraballs700 g (1.5 lb) equals one 22.5 kg (50 lb) sandbag31 g
Fibalon 3D350 g replaces 25 kg14 g
FilterBalls BluOne 1 cubic foot bag (about 1 lb) replaces two 50 lb bagsabout 10 g

Filter balls by sand capacity

Start with the sand weight on your filter’s label or in its manual. If you cannot find it, our chart of how much sand a pool filter takes lists typical capacities by tank size. Then read across:

Sand rating28 g per kg brands (Bestway, Intex, Swim & Fun, Aqualoon, VEVOR)Champlain FiltraballsFibalon 3D (350 g bags)FilterBalls (from its bag chart)
50 lb (23 kg)about 640 g (1.4 lb), one 700 g pack1 bag1 bag2 Minis
100 lb (45 kg)about 1,270 g (2.8 lb), two 700 g packs2 bags2 bags3 Minis
150 lb (68 kg)about 1,900 g (4.2 lb), three 700 g packs3 bags3 bags4 Minis
200 lb (91 kg)about 2,540 g (5.6 lb), four 700 g packs4 bags4 bags4 Minis
250 lb (113 kg)about 3,180 g (7 lb), five 700 g packs5 bags5 bags6 Minis
300 lb (136 kg)about 3,810 g (8.4 lb), six 700 g packs6 bags6 bags3 Blu

FilterBalls tells owners to use Minis in housings rated for 250 lb of sand or less and Blu above that. Its Minis counts for the smaller tanks assume a pump of 3/4 HP or less.

Intex and Bestway sand filter pumps

Intex and Bestway both publish fiber ball quantities for their own pumps. The Intex figures come from the Intex 342PO sand filter pump manual, listed by certified model number; the Bestway figures come from Bestway’s product copy for the 58475 Polysphere pack.

PumpRated flowSandFilter balls
Bestway Flowclear530 gal/h8.5 kg (18.7 lb)240 g
Bestway Flowclear1,000 gal/h18 kg (39.7 lb)500 g
Bestway Flowclear1,500 gal/h25 kg (55.1 lb)700 g
Bestway Flowclear2,000 gal/h35 kg (77.2 lb)1,000 g
Intex SF80110-21,600 GPH23 kg (50 lb)650 g (1.43 lb)
Intex SF70110-22,150 GPH35 kg (77 lb)1,000 g (2.2 lb)
Intex SF60110-22,450 GPH55 kg (120 lb)1,500 g (3.3 lb)

If your Intex pump is not one of these three, use the sand figure in its own manual and apply the 28 g per kg ratio.

A quick filter ball calculator

You can work out any tank with four steps:

  1. Find the sand weight your filter is rated for. If it is in pounds, divide by 2.2 to get kilograms.
  2. Multiply the kilograms by your brand’s ratio from the first table: 28 g for Bestway, Intex, Swim & Fun, Aqualoon and VEVOR, 31 g for Champlain, 14 g for Fibalon, about 10 g for FilterBalls.
  3. Divide by the pack size and round up to a whole pack.
  4. Fill only to your brand’s fill line and keep any spare balls in the bag.

Example: a 100 lb filter with Bestway Polysphere is 100 ÷ 2.2 = 45.5 kg, and 45.5 × 28 = about 1,270 g, so you buy three 500 g packs. For the 28 g brands there is a pounds shortcut too: pounds of sand × 0.028 = pounds of balls.

How Do You Load Filter Balls Into a Sand Filter?

Empty the tank, cover the top of the standpipe so balls cannot drop into it, and pour the balls in loosely around the standpipe until they reach your brand’s fill line. They sit directly over the laterals with no gravel or sand base, unless your filter housing’s maker specifies pea gravel under the laterals. Never pack them down hard.

The details differ by brand, so follow the bag:

  • Fill level. FilterBalls says to keep at least 12 inches of media above the laterals and suggests marking that height on the standpipe. Champlain says Filtraballs should fill about two thirds of the tank. Fibalon says to fill to the normal sand fill height, and Swim & Fun says to fill the filter container to the edge.
  • Packing. Swim & Fun and Fibalon both warn that compressed balls filter worse, and Fibalon says packed balls turn into a surface filter that clogs quickly. FilterBalls says to press gently only enough to cover the laterals. Spread them out, do not stuff them in.
  • Covering the standpipe. Champlain uses duct tape over the opening; FilterBalls suggests a plastic bag or plug. Remove it before closing the tank.
  • Gravel and leftover sand. FilterBalls says to keep pea gravel only if the housing maker specifies it. Fibalon says you do not need to remove every last grain of sand, while GRE says not to mix Aqualoon with sand or glass at all.
  • Laterals. Champlain strongly recommends replacing the standpipe and laterals on filters older than 5 years, and FilterBalls traces escaping balls to broken laterals. If the laterals and standpipe are unfamiliar, our explainer on how a pool sand filter works shows where they sit.

Emptying the old sand is the same job whatever goes back in, and our guide on how to change pool filter sand covers it. FilterBalls finishes its startup with a 30 second to 1 minute rinse, then a 30 second to 1 minute backwash, then Filter. Brands that rule out backwashing, such as Bestway, skip straight to Filter.

Do You Backwash a Filter With Balls in It?

Only if your brand says so. Bestway’s Polysphere manual states that the sand filter’s backwash function “is not applicable,” and Champlain says there is no need to backwash Filtraballs unless the gauge reaches 25 PSI. FilterBalls and Fibalon, on the other hand, are designed to be backwashed.

BrandWhat the maker says about backwashing
Bestway Flowclear PolysphereNot applicable. Hand wash the balls instead.
Champlain FiltraballsNo need unless the gauge reaches 25 PSI. Clean by removing and soaking.
Swim & Fun FilterballsRarely needed. Wash the balls at the end of the season.
GRE AqualoonMixed. GRE’s published cleaning method is machine washing, though a GRE reply on its blog says backwashing is possible.
FilterBalls (Blu, Minis)Yes. Backwash 2 to 3 minutes when pressure rises 5 to 7 PSI, typically monthly.
FibalonYes, about 80% cleanable by backwashing. Use a manual, timed backwash and do a precautionary one at season end.
IntexThe manual lists fiber ball quantities but gives no separate backwash instruction for them.

FilterBalls adds two useful notes. You will not see the puff of dirt in the sight glass that sand produces, because the release happens evenly, and some dirt staying in the media is normal. If the starting pressure after a backwash stops dropping back down, the balls need cleaning or replacing.

On Champlain’s 25 PSI figure: that is close to the 30 psi maximum working pressure in Intex’s 342PO manual, and some smaller Intex pumps are rated lower still, so on an above-ground unit treat your own pump manual’s limit and gauge zones as the ceiling.

What Pressure and Flow Should Filter Balls Run At?

Expect a lower clean pressure than you had with sand, and record it as your new baseline. FilterBalls says its media adds less than 1 PSI of back pressure, so your old sand reading no longer applies, and it says to backwash once the gauge climbs 5 to 7 PSI over that new number. On a brand that cannot be backwashed, that rise is your cue to wash the balls. Our guide to what PSI a pool filter should be at explains how to set that baseline.

That low resistance has two side effects:

  • Too much flow. Water moves through balls more freely, so flow rises. FilterBalls says too much flow lets dirt bypass the media, recommends running about 30% under the housing’s rated flow (its example is 40 gpm on a 60 gpm housing), and warns that dirt can blow off the balls when 1.5 or 2.0 HP motors are paired with filters under 200 lb.
  • Automatic valves. Fibalon says automatic backwash valves may never see enough pressure to trigger, so it tells owners to run timed backwashes by hand.

When Do Filter Balls Need Cleaning?

Clean them when the pressure has climbed and a rinse or backwash will not bring it back down, or when the balls look gray. Bestway suggests checking its balls every 4 weeks, and a retail listing for GRE’s Aqualoon suggests washing about twice a year.

Use whichever trigger comes first:

  • Pressure. A rise of 5 to 7 PSI over the clean reading, per FilterBalls. If backwashing is allowed and no longer restores that reading, a full wash is due.
  • Color. White or blue balls that have gone gray or brown are holding dirt. Bestway’s manual says balls that stay soiled or discolored after washing must be replaced.
  • Season end. Swim & Fun makes washing an end-of-season job, which also means the balls go into storage clean.
  • Cloudy water. FilterBalls lists water chemistry, too little media, the wrong media for the tank, and too much flow as the usual causes, so rule those out before blaming dirty balls.

How Do You Wash Pool Filter Balls in a Washing Machine?

Put the balls loosely in a mesh laundry bag and run a cold, delicate or synthetics cycle at 30°C (86°F) or below, with no softener and little or no soap, then air dry them. GRE’s Aqualoon instructions give that 30°C cap and the laundry bag, and Swim & Fun says its Filterballs can be machine washed without soap. Skip this method entirely for Bestway Polysphere, which is hand wash only.

Step by step:

  1. Unplug the pump. Bestway’s manual requires the pump to be unplugged before any maintenance. Open the tank according to your filter’s manual.
  2. Scoop the balls into a bucket. While the tank is open, look over the laterals and standpipe for cracks.
  3. Rinse off loose dirt. GRE’s first step is rinsing off the large dirt, which keeps grit and hair out of your washer.
  4. Bag them loosely. A mesh laundry bag on Amazon costs little and keeps the balls together in the drum. Split a big load across two bags so water can move through them.
  5. Choose a cold or synthetics cycle. Keep it at 30°C (86°F) or below. Wash the balls on their own, not with clothes.
  6. Go light on soap. Swim & Fun says no soap. If you use any detergent, use a small amount of a mild one and let the rinse run fully. No fabric softener, which is designed to coat fibers, and no bleach.
  7. Use the gentlest spin. No manufacturer we reviewed publishes a spin speed, so the lowest setting is the safe choice.
  8. Air dry, inspect, reload. Spread them out to dry, replace any that are still stained, and reload them loosely.

Can You Put Pool Filter Balls in the Dryer?

No. None of the filter ball makers we reviewed lists a clothes dryer, and every drying instruction we read is air drying. GRE says to let Aqualoon balls dry before putting them back, and Champlain tells Filtraballs owners to blot off the excess water and dry them in the sun.

There is a practical reason to respect that. GRE limits even the wash water to 30°C (86°F), a dryer adds heat on top of constant tumbling, and both Fibalon and Swim & Fun warn that crushed or compressed balls lose filtering ability. Spread the balls on a clean towel or a screen in the open air instead. Dry them fully if they are going into storage for the winter; Champlain notes that Filtraballs can also stay in the drained tank over winter.

How Do You Hand Wash Filter Balls in a Bucket?

Fill a bucket with cool water, add the balls, and swish and gently press them until the water turns murky, then dump it and repeat until it stays clear. This is the only method Bestway approves for Polysphere, and Swim & Fun lists hand washing as an alternative to the machine.

A few tips for a better hand wash:

  • Work in small batches so each ball gets moved around.
  • Press water through the balls rather than wringing or twisting them; Fibalon and Swim & Fun both warn that crushed balls filter worse.
  • Keep the water at or below the same 30°C (86°F) GRE sets for machine washing.
  • For oily or heavily soiled balls, Champlain’s method is a soak in water with a cartridge filter cleaning solution, dosed and timed by the cleaner’s own label, followed by blotting and drying in the sun.

A garden hose works for a quick refresh: put the balls in a mesh bag, spray them hard, and turn the bag a few times.

Is It Safe to Soak Filter Balls in Chlorine or Shock?

Normal pool chlorine is fine, but no maker we reviewed calls for a bleach or shock soak. Fibalon even recommends flushing the system with a standard disinfectant at the start of the season, while Champlain’s cleaning soak uses cartridge cleaner, not chlorine.

The chemicals manufacturers actually warn about are the ones that clump fiber:

  • Flocculants. GRE says flocculants make Aqualoon harden and stop filtering. Champlain bans flocculant, clarifier, phosphate remover and alum. Fibalon is designed to be used without liquid flocculants.
  • Clarifier. FilterBalls allows it, but at only one third of the dose on the bottle.

Chlorine and shock dosed into the pool water are conventional pool chemicals, which Fibalon says its fiber resists. Pouring concentrated bleach or shock straight onto the media is not on any label, so leave it out.

How Long Do Pool Filter Balls Last?

FilterBalls, Fibalon and Swim & Fun all put their balls at 3 to 5 years, VEVOR claims only 6 months to a year, and the real test is whether they still wash clean. Replace them when a wash no longer brings the pressure back to its clean reading or when they stay gray after washing.

BrandStated lifespanReplace when
FilterBallsRecycle every 3 to 5 yearsPressure no longer drops after a backwash
FibalonNormally 3 to 5 yearsNot stated
Swim & Fun Filterballs3 to 5 years in its table, though it recommends fresh balls each swim seasonStart of season
GRE AqualoonAbout 5 years (retail listing)They no longer come clean after washing
Bestway PolysphereNot stated; check each seasonStill soiled or discolored after hand washing
VEVOR6 months to a yearNot stated

When it is time, some owners move on to glass or zeolite instead. Our comparison of pool filter sand alternatives covers what each one asks of you.

Shop pool filter balls on Amazon

Why Are My Filter Balls Clumping, Escaping, or Not Clearing the Water?

Manufacturers tie clumping to packing the tank too tightly or to flocculants, escaping balls to a broken lateral or a loose standpipe, and cloudy water to chemistry, flow, or too little media. Each has a specific fix.

Clumping and matting

Fibalon warns that tightly packed balls degenerate into a surface filter and clog in a short time, and Swim & Fun says compressed balls filter worse. Pull the balls out, break up the clumps by hand, wash them, and reload loosely. If a flocculant went in recently, GRE’s warning that flocculants harden the media makes it a likely cause.

Balls showing up in the pool or the backwash line

FilterBalls traces this to a broken lateral, a misaligned standpipe, a missing diffuser plate, or another broken valve part. Any crack in the underdrain can let fiber out, so inspect all of it before refilling.

Cloudy water after switching

FilterBalls lists four causes in order: water chemistry, not enough media (less than 12 inches over the laterals), the wrong product for the tank size, and too much flow through the media. Test the water first, then check the fill depth, then turn the pump speed down if you can.

Gray or stained balls

Discoloration that survives a wash means the fiber is holding dirt it will not release. Bestway’s rule is simple: if the balls stay soiled or discolored after washing, replace them.

Frequently Asked Questions

Can you put pool filter balls in the dryer?
No manufacturer in our research approves a clothes dryer. GRE tells Aqualoon owners to let the washed balls dry, and Champlain Plastics tells Filtraballs owners to blot them and dry them in the sun. GRE also caps the wash water at 30°C (86°F), and a heated, tumbling drum is well outside anything the labels allow, so air dry them.
Do you backwash pool filter balls like sand?
It depends on the brand. Bestway says the backwash function is not applicable to its Polysphere balls, and Champlain says there is no need to backwash Filtraballs unless the gauge reaches 25 PSI. FilterBalls and Fibalon are built to be backwashed, with FilterBalls recommending 2 to 3 minutes once pressure climbs 5 to 7 PSI.
How many filter balls replace a 50 lb bag of sand?
With most brands, about 1.4 to 1.5 lb. Bestway, Intex, Swim & Fun, GRE and VEVOR all work out to roughly 28 g of balls per kilogram of sand, which is one 700 g pack per 25 kg (55 lb). Champlain rates one 1.5 lb bag per 50 lb sandbag, while Fibalon (350 g per 25 kg) and FilterBalls (half a cubic foot of Minis per 50 lb bag) use far less by weight.
Can you use laundry detergent on filter balls?
Swim & Fun says to wash its Filterballs without soap, and GRE's Aqualoon instructions do not call for any detergent. If you add anything, keep it to a very small amount of mild detergent and rinse well, because suds go straight back into the pool. None of the instructions we reviewed approve fabric softener or bleach.
How often should pool filter balls be washed?
Bestway suggests checking its Polysphere balls every 4 weeks and hand washing them when needed. Swim & Fun treats washing as an end-of-season job, and a retail listing for GRE's Aqualoon suggests about twice a year. The best trigger is your gauge: once a rinse or backwash no longer brings pressure back to the clean reading, the balls need a proper wash.
Do I need to remove all the sand before adding filter balls?
Not every grain. Fibalon says complete sand removal is not essential, though the seals should be checked and cleaned. GRE takes a stricter line and says to empty and rinse the tank and not to mix its balls with sand or glass. The one bottom layer to keep is pea gravel, and only if your filter housing's maker specifies it under the laterals.
Pool Filter Guide Editorial Team logo
Pool Filter Guide Editorial Team Independent research site

Pool Filter Guide is an independent research site. Every guide is built from manufacturer owner's manuals, spec sheets, and published standards, and names its source in the text. We do not test products in-house, and no brand pays for placement or a better verdict.

Published: