Intex Pool Filter Cartridge Types and How Often to Replace
The short answer
Which Intex cartridge fits your Krystal Clear pump, the matching Bestway types, and what Intex's own manual says about replacing above-ground cartridges.
In This Guide
An Intex cartridge pump has a screw-off filter housing with a pleated paper element inside, and every Intex owner eventually stands in a store aisle trying to remember whether they need an A, a B, or a C. The letters are not sizes in any intuitive order, the packaging changes between years, and the pump box rarely makes it past the first summer. This guide is the reference for matching an intex pool filter cartridge to the pump you actually own, with the size figures, the pack options, and an honest read on whether the cheap generic multipacks are worth buying. It also covers how often Intex and Bestway tell you to replace these above-ground cartridges, and which Bestway type matches each Intex letter.
Which Intex Filter Cartridge Do You Need?
Intex sells cartridges by letter, and the letter is set by the pump, not the pool. Intex’s own product pages list type A for the 530, 1,000 and 1,500 gph Krystal Clear cartridge pumps, type B for the 2,500 gph pump, and type H for the 330 gph pump. Type C is not a separate size: Pentair’s Pleatco cross-reference lists one element for Easy Set size “A” or “C”, and Bestway sells its matching cartridge as Type A/C. Type S1 is Intex’s hot tub cartridge, listed under its spa accessories, and does not belong in a pool pump.
The pump’s model number is on its label and in the manual, and that is the answer. Pool size, pool brand, and the box the pool came in are all unreliable proxies, because Intex sells the same pool in different pump configurations across regions and model years.
Intex Cartridge Types by Pump Model
Intex does not publish cartridge dimensions on its product pages, so the last column gives the matching element and its measurements from Pentair’s Pleatco cross-reference table.
| Type | Intex item | Fits these Krystal Clear pumps | Matching Pleatco element |
|---|---|---|---|
| A (A or C) | 29000E single, 29002E twin pack | 530, 1,000 and 1,500 gph (28603EG, 28637EG, 28635EG) | PC7-120: 4 1/4 by 8 1/8 inches, 2 inch openings |
| B | 29005E | 2,500 gph (28633EG) | PIN20: 5 7/8 by 10 1/16 inches, 1 15/16 inch openings |
| H | 29007E | 330 gph (28601EG) | PIN2H: 3 1/2 by 3 15/16 inches, 1 1/4 inch openings |
Confirm the type against the model number in your pump’s manual before ordering. Intex’s manuals note that it changes specifications without notice, so if anything about the old element looks different, trust it over a chart. If the label has worn off, pull the old element and measure the outside diameter, the length and the center openings, then match those numbers against the listing.
Most owners land on type A. If yours does, a multipack is the cheapest way to buy them.
Shop Intex type A filter cartridge 6 packs on Amazon
If your pump takes the larger element instead, an Intex type B filter cartridge is the one to look for, and it is worth ordering before midsummer when the popular sizes thin out. Owners still assembling a new pump for the first time should read how to set up an Intex pool pump and filter first, since a cartridge seated crooked in the housing lets water bypass the element entirely.
Which Bestway Cartridge Do You Need?
Bestway numbers its Flowclear cartridges by type and matches them to pump flow rate, and on two of them it also uses the Intex letter. Bestway’s US store lists these:
| Bestway type | Bestway item | Fits Flowclear pumps rated | Size Bestway lists | Also labeled |
|---|---|---|---|---|
| I | 58093E | 330 gph | 3.1 by 3.5 inches | None |
| III | 58012E | 530 to 1,500 gph (recommended for 1,000 and 1,500) | 4.2 by 8.0 inches | Type A/C |
| IV | 58095E | 2,500 gph | 5.6 by 10 inches | Type B |
Bestway’s own labels put its type III in the same size class as an Intex A or C, and its type IV with an Intex B. Treat the labels as a starting point rather than a guarantee: Bestway lists its type IV at 5.6 inches across, while Pleatco lists its Intex B equivalent at 5 7/8 inches, so compare the listed length and center openings with the element you pulled out. If you run a Flowclear pump in the 530 to 1,500 gph range, a Bestway type III filter cartridge pack is the one to look for.
For other above-ground pumps, Pleatco’s cross-reference is a useful key because each element lists every pump it fits. Its PC7-120, for example, covers the Coleco F-120, Aqua Leisure size 2, and Intex Easy Set size A or C with one 4 1/4 by 8 1/8 inch element.
How Often Should You Replace an Above-Ground Pool Filter Cartridge?
Every two weeks, by the manufacturers’ own instructions. Intex’s owner’s manual for its FP603 and FP637 Krystal Clear filter pumps says the cartridge should be “replaced at least every 2 weeks or as needed,” and its pool care section repeats the point: keep spare cartridges on hand and replace them every two weeks. Intex’s type A cartridge page and its type B and H pages say the same, and Bestway’s US store gives the same two-week figure for its Flowclear cartridges.
The reason is the media. Intex swimming pool filter cartridges use what Intex calls Dacron paper, in an element roughly the size of a coffee can, not the reinforced polyester used in inground tanks that run for several seasons. A small area of thin media loads up fast, and a rinse recovers only part of it.
The “as needed” half matters too. The manual tells you to monitor the clogging level, and the FP637 has a built-in filter gauge for it: green means the cartridge is clean, yellow means clean it, and red means clean or replace it. Press the button under the gauge to reset it after each service. Replace a cartridge early when:
- The gauge stays yellow or red after a thorough rinse. Intex’s troubleshooting table says to soak and clean it again, brushing between the pleats, and to replace it if it still cannot be cleaned.
- The pleats are torn, holed, or matted flat. The manual’s answer to a damaged cartridge is a new one.
- Flow stays weak or the water stays cloudy right after a rinse, with balanced chemistry.
Expect to use more at the start of the season, because the manual warns that the first fill can need extra filter changes. Across a 12 to 16 week swim season, a two-week swap works out to 6 to 8 cartridges, so budget for them the way you budget for chlorine. For technique, how to clean a cartridge pool filter shows how to work a fan spray into the pleats instead of just hosing the face, which decides how much each rinse actually recovers.
Genuine Intex vs Generic Cartridges
Branded Intex elements are fine, and there is nothing wrong with buying them. But they are priced per single unit at a level that makes a season expensive, and the generic multipacks are usually the better buy.
The honest comparison:
- Cost per element. Generic multipacks routinely land at a fraction of the per-element price of a branded single. Over 6 cartridges in a season that difference is meaningful.
- Media quality. Good generics use comparable paper and a comparable pleat count. Cheap ones cut pleats to save material, which reduces surface area and shortens the interval between rinses.
- Fit. This is where generics fail. An element a quarter inch short or narrow does not seal against the housing, and water takes the easy path around the outside rather than through the pleats. The pump keeps running, the pressure looks fine, and the water stays cloudy, which is a frustrating problem to diagnose.
So the buying rule for a pool filter cartridge intex replacement is simple: check the stated dimensions and the pleat count in the listing, and compare them against the element you removed. A generic that publishes real measurements matching your old cartridge is a safe buy. A listing that only says “fits Intex type A” with no numbers is a gamble. If a pack arrives and the element rattles loose in the housing or leaves a visible gap under the lid, return it rather than running it.
One more note on genuine elements. On the gauge-equipped FP637, Intex’s troubleshooting table lists an incorrect cartridge specification as one reason the gauge can read green while the cartridge is dirty, and its fix is an Intex cartridge. If you run a generic in that pump and the gauge never leaves green, inspect the cartridge rather than trusting the gauge.
The Two-Cartridge Rotation
This is the cheapest trick in above-ground pool care and almost nobody does it.
Buy a second element and keep both in service. When you rinse, do not put the wet cartridge back in. Install the dry spare, and set the freshly rinsed one somewhere sheltered to dry completely. Next rinse, swap again.
The reason it works is that dried debris flakes off paper media far better than wet debris rinses out of it. A cartridge that dries between runs sheds the fine grit packed into the pleat folds, while one that goes straight back in wet keeps compacting the same material deeper. Two elements run in rotation last noticeably longer than the same two run back to back, which is why buying a twin pack or 6 pack rather than singles is the practical move.
When to Upgrade From Cartridge to Sand
If you are replacing an intex pool pump filter cartridge every two weeks all summer, run the math before you buy another case.
Six to eight cartridges a season, even at multipack prices, adds up to roughly $30 to $60 a year. A sand filter needs one media fill that lasts 3 to 5 years, and maintenance shifts from rinsing paper every few days to a short backwash every week or two. The upfront cost of a sand system is higher, but on a pool that burns through elements at that rate the running cost typically overtakes the sand filter within a season or two. On pools much over 5,000 gallons it stops being a cost question entirely, because small paper elements simply cannot keep up with the debris load.
Intex sells sand filter pumps that connect to the same pool wall fittings and hoses, so the swap is a same-afternoon job with no plumbing. Our roundup of the best above-ground pool filters covers the sand models worth switching to, and once the tank is in place, how much sand your pool filter needs gives the fill weights by tank and model so you buy the right number of bags the first time.
If your pool is small, seasonal, and lightly used, stay with cartridges. Buy a multipack, rotate two elements, rinse properly, and the system will keep the water clear for less total money than any sand setup.
Related Guides
- How to Clean a Pool Cartridge Filter: rinsing technique that gets more out of each cartridge
- How to Set Up an Intex Pool Pump and Filter: first-time assembly and hose routing
- When to Replace a Pool Cartridge Filter: how long inground cartridges last and the pressure test for replacing them
- Best Above-Ground Pool Filter: sand and cartridge systems for when the cartridge churn stops making sense
- Pool Sand Filter Size Chart: sand weights by tank size and model
Frequently Asked Questions
Which Intex filter cartridge do I need?
Are Intex type A and type C cartridges the same?
Can I use a generic cartridge instead of a genuine Intex one?
How long does an Intex pool filter cartridge last?
What size is an Intex type A filter cartridge?
Pool Filter Guide is an independent research site. Every guide is built from manufacturer owner's manuals, spec sheets, and published standards, and names its source in the text. We do not test products in-house, and no brand pays for placement or a better verdict.