Skip to main content
13 min read Intermediate

How to Winterize an Above-Ground Pool With a Sand Filter

The short answer

Close an above-ground pool on a sand filter: when to close, how low to drain, Intex and Hayward valve settings, pump storage, and freeze repair costs.

In This Guide

To winterize an above-ground pool with a sand filter, wait until the water stays below 65°F, balance and shock it, backwash one last time, then lower the water below the skimmer and return. After that you drain the filter tank through its bottom cap, park the valve in the storage position your manual names, drain the pump and bring it indoors, and cover the pool. Intex and Bestway frame pools are different: their manuals say to take the pool down for winter instead of closing it.

Which closing method does your pool and filter need?

Two different setups share this name, and their manuals ask for different things. Intex and Bestway frame pools usually run a small all-in-one sand filter pump, while hard-sided steel or resin pools usually run a full-size tank such as a Hayward ProSeries with a separate pump.

StepIntex sand filter pumpBestway FlowclearHayward ProSeries (full-size)
The pool in winterTake down below 41°F (Intex Ultra XTR manual)Disassemble for winter (Bestway Steel Pro manual)Stays up with the water lowered
Valve storage settingPointer on “N”Not given in the manualPointer between any two positions
Draining the tankDrain valve cap at bottom of tankDrain valve cap at bottom of tankDrain cap at base, left off all winter
The sandNo removal stepPour it all out and dry the partsNo removal step, just drain the water
The pumpMotor off the tank base, stored at 32°F to 104°FStore dry, out of children’s reachDrain the strainer body, store in a dry enclosure
AntifreezePropylene glycol onlyNot coveredPropylene glycol only

Sources: Intex’s sand filter pump manual (models SF80110-2, SF70110-2 and SF60110-2), Bestway’s Flowclear 58404 manual, and Hayward’s ProSeries (IS210T Rev J) and PowerFlo Matrix pump manuals.

When should you close an above-ground pool?

Close it when the water temperature holds below 65°F, not on a calendar date. HTH and Leslie’s both use that line, because warmer water under a cover keeps feeding algae. Clorox Pool’s guide uses daytime air under 70°F, a looser cue that lands a little earlier.

Frame pools have a second, harder deadline. Intex’s Ultra XTR manual says you “must drain, disassemble and properly store the pool when the temperature drops below 41 degrees Fahrenheit (5 degrees Celsius) to prevent ice damage.” Bestway’s Steel Pro manual is just as direct: it strongly recommends taking the pool down during the off season. If you live where winter regularly dips below 41°F, plan the takedown, not a closing.

How do you balance and shock the water before closing?

Test and adjust several days before closing day, as Inyo Pools’ above-ground closing guide does, so the chemicals have time to work. Hayward’s ProSeries manual lists these targets:

  • pH: 7.2 to 7.6
  • Total alkalinity: 80 to 120 ppm
  • Calcium hardness: 200 to 400 ppm (Inyo Pools’ above-ground closing guide uses a tighter 175 to 250 ppm)
  • Free chlorine: 1.0 to 3.0 ppm, with combined chlorine no higher than 0.2 ppm
  • Cyanuric acid: 60 to 80 ppm

Shock once pH and alkalinity are in range, with the filter running so it mixes through. Clorox Pool’s closing sequence puts the shock before the winter algaecide, and the closing kit label sets the wait between them.

How do you clean the pool before closing it?

Brush the walls and floor, empty the skimmer and pump baskets, and vacuum, because anything left on the floor sits under the cover for months. Pull out the ladder, toys and solar cover; Intex’s manual also has you remove anything attached to the strainer connector.

Vacuuming is also the easiest time to start lowering the water. Hayward’s manual names Waste as the setting that bypasses the filter “for draining or lowering water level,” Intex’s 6-way valve has the same Waste position, and Inyo Pools’ closing guide vacuums to waste for exactly this reason.

How do you backwash the sand filter for the last time?

Backwash until the sight glass runs clear, then rinse, so the sand bed goes into winter clean. Hayward’s manual says backwash takes about 2 minutes or less depending on the dirt load, followed by Rinse for about 1/2 to 1 minute. Both Hayward and Intex tell you to shut the pump off every time you move the valve handle.

Intex units add a built-in timer on many models and a waste port that has to be uncapped first, so follow our steps for backwashing an Intex sand filter on those. For a Hayward, Pentair or other top-mount multiport, the standard sand filter backwash procedure applies.

How low should the water be in an above-ground pool for winter?

On a hard-sided pool, lower the water just below the skimmer opening and the return fitting, and stop there. Hayward’s PowerFlo Matrix pump manual puts it as draining the water level “below all inlets to the pool,” and Inyo Pools’ closing guide says the same about the returns and skimmer. Never empty a hard-sided above-ground pool: Inyo warns that hydrostatic pressure can damage a fully drained one.

If your skimmer takes a winter plate or skimmer guard, you can keep the water higher; Pool Corporation’s above-ground owner guide offers that as the alternative to dropping the level. The plate has to seal well, or the skimmer throat fills and freezes.

Intex pools follow their own rule. Below 41°F, the answer is to drain the pool and take it down. Where winters stay above 41°F, Intex’s manual lets you leave it up: plug the inlet and outlet from inside on pools 16 feet and smaller, or close the plunger valves on pools 17 feet and larger, then disconnect the hoses.

How do you disconnect the hoses and plug the wall fittings?

Unplug the pump first, then disconnect every hose between the pool, pump and filter and let them drain. On an Intex pool you are taking down, the manual has you remove the strainers and plunger valves from the wall once the pool is empty. On a hard-sided pool, the skimmer and return fittings stay in the wall and get winter plugs.

To clear water from the fittings and any rigid pipe, use a shop vacuum set to blow. Hayward’s pump manual allows only “a low pressure (below 5 PSI), high volume blower,” because compressed air can make components explode, and Intex’s manual says never to test its pump with compressed air.

Then thread a winter plug into the return. A set of above-ground pool winterizing plugs is inexpensive; check the thread size against your fitting first. Hayward’s manual warns that plugs left in suction outlets raise the risk of suction entrapment, so every plug comes out before the pump restarts in spring.

How do you drain the sand filter tank?

Unscrew the drain cap at the bottom of the tank and let the water run out until it stops. On an Intex sand filter pump, the manual says to turn the drain valve cap counterclockwise; on a Hayward ProSeries, the drain cap sits at the base of the tank. Open the air relief valve on top while it drains, or the tank pulls a vacuum and holds water back.

Hayward’s instruction is to “leave cap off during winter,” which is good practice on any brand. Bag the cap and gasket with the other small parts and tie the bag to the valve handle. If a Hayward cap does go missing, Leslie’s notes that the SX180LA fits tanks made after 2005 and the SX180HG fits older ones; SX180LA listings run about $8 to $14.

For the tank-level detail, including where water hides in the laterals, see our guide on how to winterize a pool filter, which also covers in-ground systems and other filter types.

Which valve position do you use for winter storage?

Use the position your manual names, and on most above-ground sand filters that is not Closed. Hayward’s ProSeries manual says to press the Vari-Flo handle down and rotate it “so as to set pointer on valve top between any two positions,” which lets water drain from the valve, and to leave it in that inactive spot. If your valve top has a mark labeled Winter or Winterize, that detent does the same job.

Intex’s 6-way valve has its own storage mark. The manual says to depress the handle, set the pointer on the “N” position, which “allows the water to drain from the valve,” and leave it there. If your Intex valve shows no N, check the storage section of your model’s manual.

Closed blocks flow; it is not a storage setting. Intex describes it as shutting off all flow to the filter and pool, and Hayward as shutting off flow from the pump to the filter. Pentair’s Sand Dollar spec sheet lists six positions (Filter, Waste, Backwash, Closed, Rinse, Recirculate) with no winter mark, so follow the storage instruction in the Pentair owner’s guide.

While you are at the valve, unscrew the pressure gauge and store it indoors with the drain cap. On a Hayward valve it threads into a 1/4 inch NPT port, and the manual calls for two turns of PTFE tape when it goes back in.

How do you winterize an Intex or Bestway sand filter pump?

Intex’s long term storage procedure treats the sand filter pump as something that comes apart and goes indoors. Once the pool itself is drained, the manual’s steps are:

  1. Unplug the unit and disconnect all hoses.
  2. Unscrew the drain valve cap and let the tank empty.
  3. Take the pump motor off the tank base.
  4. Let the pieces and hoses air dry outside.
  5. Coat the L-shape O-rings, pump hose O-rings, strainer valve step washers and flat strainer washers with petroleum jelly.
  6. Set the 6-way valve to “N.”
  7. Store everything dry, ideally in the original box, between 32°F and 104°F.

Do not wrap the motor in a plastic bag. Intex warns that plastic traps condensation and corrodes the motor. If the reassembly in spring feels unfamiliar, our guide to setting up an Intex pool pump and filter walks through the hose and plunger valve connections again.

Bestway’s Flowclear manual is simpler and stricter on the sand. Its winterizing steps are to backwash, drain the pool, unscrew the drain valve cap at the bottom of the tank, disconnect the two hoses, “completely pour the sand out of the tank and dry all components,” and store the filter somewhere dry and out of children’s reach. Both brands say plainly that letting water freeze in the filter damages it and voids the warranty.

How do you winterize a Hayward ProSeries or other full-size sand filter?

Full-size tanks usually stay outside on the pad, drained, with the cap off. They are heavy: Hayward’s spec table lists 100 pounds of sand for the S166T, 150 for the S180T, 200 for the S210T and 300 for the S244T, and Pentair’s Sand Dollar line runs from 100 pounds (SD35) to 350 pounds (SD80). Hayward’s own winter steps are only three: drain the tank and leave the cap off, park the valve between two positions, and winterize the pump per its manual.

The pump comes inside. Hayward’s PowerFlo Matrix owner’s manual gives the sequence: turn the power off, remove the drain plug from the bottom of the strainer body, disconnect the pump from its base, put the lid and plug back once it has drained, and store it in a dry enclosure with the motor covered but never wrapped in plastic film. The same manual says a frozen pump voids the warranty. The ProSeries manual also states that Hayward pumps are meant for permanently installed pools, “do not use with storable pools,” which is why these systems sit beside hard-sided pools rather than Intex or Bestway frame pools.

Should you leave the sand in the tank or replace it now?

Leave it in on Hayward, Pentair and similar full-size tanks, and on Intex units the manual gives no removal step either. The sand is not the freeze risk; standing water is. Bestway is the one brand here that wants the sand poured out, so follow its manual on Flowclear units.

If the sand is due for a change, either end of the season works. Swapping at closing lets you inspect the laterals while the tank is empty; swapping in spring folds the new sand’s first backwash into startup, and Hayward’s manual calls for at least 2 minutes of it to clear the fines. Our guide on how often to change pool filter sand covers the signs that the bed is worn out.

What winter chemicals and cover does an above-ground pool need?

Add the winterizing chemicals from your closing kit at the dose on its label. Intex’s manual says requirements vary by region and suggests asking a local pool dealer. If you add antifreeze to any plumbing, use propylene glycol only; Intex and Hayward both warn that other antifreezes are toxic and can damage plastic parts.

Hard-sided pools get an air pillow under the cover. Inyo Pools’ guide has you inflate it with a leaf blower or shop vac, tie it off in the center of the pool, and use two or more on larger pools. Robelle’s listing for its 4 by 8 foot pillow says to fill it only halfway to two-thirds so it does not pop under ice. A pool air pillow takes the pressure of expanding ice so the walls do not have to, and because ice is less dense than liquid water, as the USGS explains, frozen pool water takes up about 9 percent more space than it did as liquid. That expansion is what the pillow absorbs.

Lay the cover over the pillow and secure it with the cable and winch that run through its grommets, tightened under the top ledge. In windy spots, Inyo suggests a cover seal wrap around the pool, and Robelle’s listings mention cover clips for the same reason. Intex’s own manual notes that its pool cover is not a safety cover.

Shop above-ground pool winter covers on Amazon

What should you check over the winter?

A closed pool still needs regular checks, especially after storms:

  • Water on the cover. Pump off rain and snowmelt with a cover pump, as Inyo recommends, before the weight drags the cover in.
  • The air pillow. It should still be centered and partly inflated.
  • Cable tension. Retighten the winch after wind or ice storms.
  • The filter tank. The drain cap should still be off and the tank empty; drain any rain or snowmelt before the next freeze.
  • Indoor equipment. Pumps and motors should be dry, unwrapped, and inside the 32°F to 104°F range Intex gives for storage.
  • Mild-winter frame pools. If an Intex pool stayed up, take it down if the forecast heads below 41°F.

What winterizing mistakes crack sand filters and pumps?

Almost every freeze failure traces back to water left where it can expand, and none of it is covered: Intex says freezing voids its warranty, and Hayward’s one-year filter warranty excludes damage from freezing. The prices below are typical ranges seen across several retailer listings.

MistakeWhat breaksTypical replacement cost
Tank not fully drained, or cap put back on outdoorsCracked filter tankHayward W3S166T filter about $389 to $429; W3S210T about $569; Intex SX2100 (26645EG) sand filter pump about $204 to $270
Valve left on Filter or Closed with water insideSplit valve bodyHayward SP0714T valve about $135 to $275; Intex 6-way valve about $45 to $110
Water left in the pump strainer bodyCracked pump housingNew Hayward PowerFlo Matrix 1 HP pump about $480 to $510
Gauge left on the valveFrozen or cracked gaugeHayward ECX270861 about $9 to $15
Drain cap thrown out or lostNothing, until springHayward SX180LA about $8 to $14

Rain is the sneaky one. A tank left outdoors with the drain cap screwed back on and the valve parked open lets rain and snowmelt in with no way out, so it can refill between freezes. Leave the cap off, as Hayward says, and the water drains as fast as it arrives.

Two more mistakes cost money in other ways. A compressor used in place of a low pressure blower is what Hayward flags as an explosion hazard, and closing while the water is still warm can mean opening to a green pool.

What happens at spring opening?

Opening runs the closing in reverse: pull every winter plug, reinstall the drain cap and gauge, set the valve back to Filter, refill to the middle of the skimmer, prime the pump, and backwash before the first filter cycle. Our guide on how to use a pool sand filter covers the start-up order, including the first start after winter.

Frequently Asked Questions

Do you leave the sand in an above-ground sand filter over winter?
On a full-size tank like a Hayward ProSeries, yes. The manual only asks you to drain the water and leave the drain cap off, and the sand stays put. Bestway is the exception: its Flowclear manual tells you to pour the sand out and dry every part before storage.
What valve setting do you use to winterize a sand filter?
It depends on the brand. Hayward has you press the handle down and park the pointer between any two positions, while Intex has you set the pointer on the N position. Do not use Closed on either one, because that setting is meant to block flow, not to let the valve drain.
Can I leave an Intex frame pool up all winter?
Only where it never gets cold. Intex's manual says to drain, take down and store the pool once temperatures drop below 41°F (5°C). Below that point, ice can damage the liner, the frame and the fittings.
Can a sand filter stay outside over winter?
A drained full-size tank can stay on its pad with the drain cap off, which is how Hayward's manual leaves it. The pump should still go into a dry enclosure. Intex and Bestway both want their sand filter pumps stored in a dry place, and Intex gives a storage range of 32°F to 104°F.
Do I need antifreeze in an above-ground pool's plumbing?
Most above-ground setups do not, because the hoses come off and drain completely. If you do use it, Intex and Hayward both say propylene glycol is the only safe type. Other antifreezes are toxic and can damage plastic parts.
Pool Filter Guide Editorial Team logo
Pool Filter Guide Editorial Team Independent research site

Pool Filter Guide is an independent research site. Every guide is built from manufacturer owner's manuals, spec sheets, and published standards, and names its source in the text. We do not test products in-house, and no brand pays for placement or a better verdict.

Published: